RM新时代注册
<optgroup id="rs0uz"><var id="rs0uz"></var></optgroup>
<menu id="rs0uz"></menu>

    1. <optgroup id="rs0uz"><var id="rs0uz"></var></optgroup>

    2. <menuitem id="rs0uz"></menuitem>
    3. 歡迎您訪問萊州聚峰機械有限公司網站!
      點擊撥打服務熱線:400-879-1999
      大家都在搜: 鏟斗外翻 3.5噸A后側 3.5噸A后尾

      自動上料攪拌機機械漏油的幾個問題

      來源:http://www.bestinko.com/日期:2022-12-21

      概述:自動上料攪拌機工作量大,用戶只要具備一定的專門的維修知識,對使用會(huì )有很大幫助。不過,機械漏油是很常見的問題,今天就教大家這些小技巧
      自動上料攪拌機工作量大,用戶只要具備一定的專門的維修知識,對使用會(huì )有很大幫助。不過,機械漏油是很常見的問題,今天就教大家這些小技巧。
      The workload of the automatic feeding mixer is large. As long as the user has some special maintenance knowledge, it will be very helpful to use it. However, mechanical oil leakage is a common problem. Today, I will teach you these tips.
      過度使用和油封是正常磨損情況。方法:更換新油封即可。
      Excessive use and oil seals are normal wear conditions. Solution: Replace the oil seal with a new one.
      長時間不更換機油,濾芯質量不合格,機油太臟,加速油封磨損。方法:盡快更換液壓油和濾芯。
      If the engine oil is not replaced for a long time, the filter element is unqualified, the engine oil is too dirty, and the oil seal is accelerated to wear. Solution: Replace the hydraulic oil and filter element as soon as possible.
      傳動軸平衡失效,擺動大,造成主軸擺動油封偏磨。方法:及時糾正并更換轉軸。液壓油變質乳化,導致潤滑性能下降,加速油封磨損。方法:盡快更換液壓油和濾芯,嚴重時需要清洗系統。泵支架松動,開泵,泵固定螺栓松動,進而引起液壓泵整體振動和油封磨損。
      The balance of the transmission shaft fails and the swing is large, causing eccentric wear of the main shaft swing oil seal. Solution: Correct and replace the shaft in time. The hydraulic oil is deteriorated and emulsified, which leads to the decline of lubricating performance and accelerates the wear of oil seals. Solution: replace the hydraulic oil and filter element as soon as possible, and clean the system in serious cases. The pump bracket is loose, the pump is started, and the pump fixing bolts are loose, which causes the overall vibration of the hydraulic pump and the wear of the oil seal.
      自動上料攪拌機
      自動上料攪拌系統回油不暢,回油管和散熱器堵塞,進而導致電機殼內壓力升高,造成油封漏油。方法:堵塞物,保持回油循環通暢。如果散熱器不散熱,油溫過高,粘度和潤滑性下降,油封過熱,密封失效。方法:對散熱器進行故障排除,對系統進行冷卻過程,避免泵電機磨損。嚴重時,停止發動機并熄火,用水沖洗泵電機和散熱器外殼,以達到冷卻效果。
      The oil return of the automatic feeding and mixing system is not smooth, and the oil return pipe and radiator are blocked, which leads to the pressure rise in the motor housing and oil leakage of the oil seal. Solution: Remove the blockage and keep the oil return circulation smooth. If the radiator does not dissipate heat, the oil temperature is too high, the viscosity and lubricity are reduced, the oil seal is overheated, and the seal fails. Solution: Troubleshoot the radiator and cool the system to avoid wear of the pump motor. In serious cases, stop the engine and shut down, flush the pump motor and radiator housing with water to achieve cooling effect.
      此外您要注意,經常檢查和排除自動上料攪拌機可能出現的故障,防止和避免故障。更多相關內容就來我們網站http://www.bestinko.com進行咨詢吧!
      In addition, you should always check and eliminate the possible faults of the automatic feeding mixer to prevent and avoid them. More relevant content will come to our website http://www.bestinko.com Consult!

      截屏,微信識別二維碼

      RM新时代注册
      <optgroup id="rs0uz"><var id="rs0uz"></var></optgroup>
      <menu id="rs0uz"></menu>

      1. <optgroup id="rs0uz"><var id="rs0uz"></var></optgroup>

      2. <menuitem id="rs0uz"></menuitem>
      3. RM新时代官网 RM新时代官网 RM新时代登录网址 RM新时代 RM新时代是什么平台
        <optgroup id="rs0uz"><var id="rs0uz"></var></optgroup>
        <menu id="rs0uz"></menu>

        1. <optgroup id="rs0uz"><var id="rs0uz"></var></optgroup>

        2. <menuitem id="rs0uz"></menuitem>
        3. RM新时代投资官网 RM新时代反波胆app rm新世界反波胆下载 RM新时代首页 RM新时代资金盘 RM新时代反波胆靠谱吗 新时代反波胆 RM新时代首页 rm新时代足球交易平台 RM新时代反波胆最新消息